Contents x
    Registry and Install Settings
    • 28 May 2025
    • 2 Minutes to read
    • Contributors
    • Dark
      Light
    • PDF
    Contents

    Registry and Install Settings

    • Updated on 28 May 2025
    • 2 Minutes to read
    • Contributors
    • Dark
      Light
    • PDF
    Article summary

    NOTE

    Not all settings may be set during installation. Settings listed below that do not have a value in the Parameter Name column must be set via the registry keys affected settings with group policy, HCIDeploy, or some other post installation method.

    ENCRYPTION METHODS

    Encryption Methods: Please note that If you are looking to enable AES encryption, choose one of the RIJNDAEL options. ExactAccess was developed before the Advanced Encryption Standard was finalized. It was unclear which of several methods would become the new AES recommendation, so we chose to support all of the methods that were present in the final rounds of selection. These include: RIJNDAEL (the selected standard), TWOFISH, and SERPENT.

    REQUIRED SETTINGS
    SERVER CONNECTION PROPERTIES

    REQUIRED SETTINGS

    X_RUN_CONFIG

    DESCRIPTION: Enable/Disable running the configuration tool during silent installation.

    VALUES
    0 to disable configuration tool execution
    1 (default) to disable configuration tool execution

    IMPORTANT

    Silent installation will not complete unless this parameter is added and set to 0

    XA_MODE

    DESCRIPTION: Client Mode (SUM, KM, VMVDI, CITRIXVDI, RSM)

    VALUES
    1=KM
    2=RSM
    4=SUM (DEFAULT)
    5=VMVDI
    6=CITRIXVDI

    VDI TYPE

    Be sure to specify the correct VDI type when installing under the respective VM technologies.

    • Use VMVDI for VMware servers
    • Use CitrixVDI for Citrix VM servers.

    AFFECTED REGISTRY SETTING(S):

    HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\ExactAccess
ApplicationMode:reg_dword

    SERVER CONNECTION PROPERTIES

    Settings apply to all modes unless otherwise indicated

    XA_SRV

    DESCRIPTION: Primary XA (SSO) server name (must be a valid server NETBIOS or FQDN Name or IP address)

    AFFECTED REGISTRY SETTING(S):

    HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\ExactAccess\Servers\INDY
0000: reg_sz

    XA_AUDIT_SRV

    DESCRIPTION: Primary Audit server name (must be a valid audit server NETBIOS or FQDN Name or IP address)

    AFFECTED REGISTRY SETTING(S):

    HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\AuditServerClient\Connection\INDY
0000: reg_sz

    XA_PRX_SRV

    DESCRIPTION: Primary prox server name (must be a valid server NETBIOS or FQDN Name or IP address)

    AFFECTED REGISTRY SETTING(S):

    XA_PRX_SRV ALL HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\ProxCardClient\Indy
0000: reg_sz

    X_D_SRV

    DESCRIPTION: Primary hciDeploy server name (must be a valid server NETBIOS or FQDN Name or IP address)

    AFFECTED REGISTRY SETTING(S):

    X_D_SRV ALL HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\HCIDeployClient\Indy
0000: reg_sz

    X_RA_SRV

    DESCRIPTION: Primary Remote Authentication server name (must be a valid server NETBIOS or FQDN Name or IP address)

    AFFECTED REGISTRY SETTING(S):

    X_RA_SRV KM HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\HCCitrixSessionDirectory\INDY
0000: reg_sz

    X_PREF_IPV4

    DESCRIPTION: Indicates that any TCP/IP communication prefers to use IPv4 when IPv6 is installed and available. This setting will be ignored if the _SRV setting(s) listed above contain a direct IPv6 address.

    AFFECTED REGISTRY SETTING(S):

    X_PREF_IPV4 ALL HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\ProxCardClient
PreferIPv4: reg_dword

    HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\ExactAccess
PreferIPv4: reg_dword

    HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\AuditServerClient
PreferIPv4: reg_dword

    HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\HCCitrixSessionDirectory
PreferIPv4: reg_dword

    HKEY_LOCAL_MACHINE\SOFTWARE\HealthCast\HCIDeployClient
PreferIPv4: reg_dword
    Was this article helpful?
    What's Next